Attribute VB_Name = "modDP5Configuration"
Option Explicit

Public s As New CSCommon

Public Function GetCmdDesc(ByVal strCmd As String) As String
    Dim strCmdName As String
    Select Case strCmd
        Case "RESC"
            strCmdName = "Reset Configuration"
        Case "CLCK"
            strCmdName = "20MHz/80MHz"
        Case "TPEA"
            strCmdName = "Peaking Time"
        Case "GAIF"
            strCmdName = "Fine Gain"
        Case "GAIN"
            strCmdName = "Total Gain (Analog * Fine)"
        Case "RESL"
            strCmdName = "Detector Reset Lockout"
        Case "TFLA"
            strCmdName = "Flat Top"
        Case "TPFA"
            strCmdName = "Fast Channel Peaking Time"
        Case "RTDE"
            strCmdName = "RTD On/Off"
        Case "MCAS"
            strCmdName = "MCA Source"
        Case "RTDD"
            strCmdName = "Custom RTD Oneshot Delay"
        Case "RTDW"
            strCmdName = "Custom RTD Oneshot Width"
        Case "PURE"
            strCmdName = "PUR Interval On/Off"
        Case "SOFF"
            strCmdName = "Set Spectrum Offset"
        Case "INOF"
            strCmdName = "Input Offset"
        Case "ACKE"
            strCmdName = "ACK / Don't ACK Packets With Errors"
        Case "AINP"
            strCmdName = "Analog Input Pos/Neg"
        Case "AUO1"
            strCmdName = "AUX_OUT Selection"
        Case "AUO2"
            strCmdName = "AUX_OUT2 Selection"
        Case "BLRD"
            strCmdName = "BLR Down Correction"
        Case "BLRM"
            strCmdName = "BLR Mode"
        Case "BLRU"
            strCmdName = "BLR Up Correction"
        Case "BOOT"
            strCmdName = "Turn Supplies On/Off At Power Up"
        Case "CUSP"
            strCmdName = "Non-Trapezoidal Shaping"
        Case "DACF"
            strCmdName = "DAC Offset"
        Case "DACO"
            strCmdName = "DAC Output"
        Case "GAIA"
            strCmdName = "Analog Gain Index"
        Case "GATE"
            strCmdName = "Gate Control"
        Case "GPED"
            strCmdName = "G.P. Counter Edge"
        Case "GPGA"
            strCmdName = "G.P. Counter Uses GATE?"
        Case "GPIN"
            strCmdName = "G.P. Counter Input"
        Case "GPMC"
            strCmdName = "G.P. Counter Cleared With MCA Counters?"
        Case "GPME"
            strCmdName = "G.P. Counter Uses MCA_EN?"
        Case "HVSE"
            strCmdName = "HV Set"
        Case "MCAC"
            strCmdName = "MCA/MCS Channels"
        Case "MCAE"
            strCmdName = "MCA/MCS Enable"
        Case "MCSL"
            strCmdName = "MCS Low Threshold"
        Case "MCSH"
            strCmdName = "MCS High Threshold"
        Case "MCST"
            strCmdName = "MCS Timebase"
        Case "PAPS"
            strCmdName = "Preamp 8.5/5 (N/A)"
        Case "PAPZ"
            strCmdName = "Pole-Zero"
        Case "PDMD"
            strCmdName = "Peak Detect Mode (Min/Max)"
        Case "PRCL"
            strCmdName = "Preset Counts Low Threshold"
        Case "PRCH"
            strCmdName = "Preset Counts High Threshold"
        Case "PREC"
            strCmdName = "Preset Counts"
        Case "PRER"
            strCmdName = "Preset Real Time"
        Case "PREL"
            strCmdName = "Preset Live Time"
        Case "PRET"
            strCmdName = "Preset Time"
        Case "RTDS"
            strCmdName = "RTD Sensitivity"
        Case "RTDT"
            strCmdName = "RTD Threshold"
        Case "SCAH"
            strCmdName = "SCAx High Threshold"
        Case "SCAI"
            strCmdName = "SCA Index"
        Case "SCAL"
            strCmdName = "SCAx Low Theshold"
        Case "SCAO"
            strCmdName = "SCAx Output (SCA1-8 Only)"
        Case "SCAW"
            strCmdName = "SCA Pulse Width (Not Indexed - SCA1-8)"
        Case "SCOE"
            strCmdName = "Scope Trigger Edge"
        Case "SCOG"
            strCmdName = "Digital Scope Gain"
        Case "SCOT"
            strCmdName = "Scope Trigger Position"
        Case "TECS"
            strCmdName = "TEC Set"
        Case "THFA"
            strCmdName = "Fast Threshold"
        Case "THSL"
            strCmdName = "Slow Threshold"
        Case "TLLD"
            strCmdName = "LLD Threshold"
        Case "TPMO"
            strCmdName = "Test Pulser On/Off"
        Case "VOLU"
            strCmdName = "Speaker On/Off"
        Case "CON1"
            strCmdName = "Connector 1"
        Case "CON2"
            strCmdName = "Connector 2"
    End Select
    GetCmdDesc = strCmdName
End Function

Public Function CreateFullReadBackCmd() As String
    Dim strCfg As String
    Dim isHVSE As Boolean
    Dim isPAPS As Boolean
    Dim isTECS As Boolean
    Dim isVOLU As Boolean
    Dim isCON1 As Boolean
    Dim isCON2 As Boolean
    Dim isINOF As Boolean
    Dim isBOOT As Boolean
    Dim isGATE As Boolean
    Dim isPAPZ As Boolean
    Dim isSCTC As Boolean
    Dim isDP5_DxK As Boolean
    Dim isDP5_DxL As Boolean
    
    If (STATUS.DEVICE_ID = dppMCA8000D) Then
        strCfg = CreateFullReadBackCmdMCA8000D()
        CreateFullReadBackCmd = strCfg
        Exit Function
    End If
    
    ' DP5 Rev Dx K,L needs PAPZ
    If ((STATUS.DEVICE_ID = dppDP5) And STATUS.isDP5_RevDxGains) Then
        If ((STATUS.DPP_ECO And &HF) = &HA) Then
            isDP5_DxK = True
        End If
        If ((STATUS.DPP_ECO And &HF) = &HB) Then
            isDP5_DxL = True
        End If
    End If

    isHVSE = CBool(((STATUS.DEVICE_ID <> dppPX5) And STATUS.PC5_PRESENT) Or (STATUS.DEVICE_ID = dppPX5))
    isPAPS = CBool((STATUS.DEVICE_ID <> dppDP5G) And (STATUS.DEVICE_ID <> dppTB5))
    isTECS = CBool(((STATUS.DEVICE_ID = dppDP5) And STATUS.PC5_PRESENT) Or (STATUS.DEVICE_ID = dppPX5) Or (STATUS.DEVICE_ID = dppDP5X))
    isVOLU = CBool(STATUS.DEVICE_ID = dppPX5)
    
    isCON1 = CBool((STATUS.DEVICE_ID <> dppDP5) And (STATUS.DEVICE_ID <> dppDP5X))
    isCON2 = CBool((STATUS.DEVICE_ID <> dppDP5) And (STATUS.DEVICE_ID <> dppDP5X))
    
    isINOF = CBool((STATUS.DEVICE_ID <> dppDP5G) And (STATUS.DEVICE_ID <> dppTB5))
    isSCTC = CBool((STATUS.DEVICE_ID = dppDP5G) Or (STATUS.DEVICE_ID = dppTB5))
    isBOOT = CBool((STATUS.DEVICE_ID = dppDP5) Or (STATUS.DEVICE_ID = dppDP5X))
    
    isGATE = CBool((STATUS.DEVICE_ID = dppDP5) Or (STATUS.DEVICE_ID = dppDP5X))
    isPAPZ = CBool((STATUS.DEVICE_ID = dppPX5) Or isDP5_DxK Or isDP5_DxL)
    
    strCfg = ""
    strCfg = strCfg & "RESC=?;"
    strCfg = strCfg & "CLCK=?;"
    strCfg = strCfg & "TPEA=?;"
    strCfg = strCfg & "GAIF=?;"
    strCfg = strCfg & "GAIN=?;"
    strCfg = strCfg & "RESL=?;"
    strCfg = strCfg & "TFLA=?;"
    strCfg = strCfg & "TPFA=?;"
    strCfg = strCfg & "PURE=?;"
    If (isSCTC) Then strCfg = strCfg & "SCTC=?;"
    strCfg = strCfg & "RTDE=?;"
    strCfg = strCfg & "MCAS=?;"
    strCfg = strCfg & "MCAC=?;"
    strCfg = strCfg & "SOFF=?;"
    strCfg = strCfg & "AINP=?;"
    If (isINOF) Then strCfg = strCfg & "INOF=?;"
    strCfg = strCfg & "GAIA=?;"
    strCfg = strCfg & "CUSP=?;"
    strCfg = strCfg & "PDMD=?;"
    strCfg = strCfg & "THSL=?;"
    strCfg = strCfg & "TLLD=?;"
    strCfg = strCfg & "THFA=?;"
    strCfg = strCfg & "DACO=?;"
    strCfg = strCfg & "DACF=?;"
    strCfg = strCfg & "RTDS=?;"
    strCfg = strCfg & "RTDT=?;"
    strCfg = strCfg & "BLRM=?;"
    strCfg = strCfg & "BLRD=?;"
    strCfg = strCfg & "BLRU=?;"
    If (isGATE) Then strCfg = strCfg & "GATE=?;"
    strCfg = strCfg & "AUO1=?;"
    strCfg = strCfg & "PRET=?;"
    strCfg = strCfg & "PRER=?;"
    strCfg = strCfg & "PREC=?;"
    strCfg = strCfg & "PRCL=?;"
    strCfg = strCfg & "PRCH=?;"
    If (isHVSE) Then strCfg = strCfg & "HVSE=?;"
    If (isTECS) Then strCfg = strCfg & "TECS=?;"
    If (isPAPZ) Then strCfg = strCfg & "PAPZ=?;"
    If (isPAPS) Then strCfg = strCfg & "PAPS=?;"
    strCfg = strCfg & "SCOE=?;"
    strCfg = strCfg & "SCOT=?;"
    strCfg = strCfg & "SCOG=?;"
    strCfg = strCfg & "MCSL=?;"
    strCfg = strCfg & "MCSH=?;"
    strCfg = strCfg & "MCST=?;"
    strCfg = strCfg & "AUO2=?;"
    strCfg = strCfg & "TPMO=?;"
    strCfg = strCfg & "GPED=?;"
    strCfg = strCfg & "GPIN=?;"
    strCfg = strCfg & "GPME=?;"
    strCfg = strCfg & "GPGA=?;"
    strCfg = strCfg & "GPMC=?;"
    strCfg = strCfg & "MCAE=?;"
    If (isVOLU) Then strCfg = strCfg & "VOLU=?;"
    If (isCON1) Then strCfg = strCfg & "CON1=?;"
    If (isCON2) Then strCfg = strCfg & "CON2=?;"
    If (isBOOT) Then strCfg = strCfg & "BOOT=?;"
    CreateFullReadBackCmd = strCfg
End Function

Public Function CreateFullReadBackCmdMCA8000D() As String
    Dim strCfg As String
    strCfg = ""
    If (STATUS.DEVICE_ID = dppMCA8000D) Then
        strCfg = strCfg & "RESC=?;"
        strCfg = strCfg & "PURE=?;"
        strCfg = strCfg & "MCAS=?;"
        strCfg = strCfg & "MCAC=?;"
        strCfg = strCfg & "SOFF=?;"
        strCfg = strCfg & "GAIA=?;"
        strCfg = strCfg & "PDMD=?;"
        strCfg = strCfg & "THSL=?;"
        strCfg = strCfg & "TLLD=?;"
        strCfg = strCfg & "GATE=?;"
        strCfg = strCfg & "AUO1=?;"
        strCfg = strCfg & "PRER=?;"
        strCfg = strCfg & "PREL=?;"
        strCfg = strCfg & "PREC=?;"
        strCfg = strCfg & "PRCL=?;"
        strCfg = strCfg & "PRCH=?;"
        strCfg = strCfg & "SCOE=?;"
        strCfg = strCfg & "SCOT=?;"
        strCfg = strCfg & "SCOG=?;"
        strCfg = strCfg & "MCSL=?;"
        strCfg = strCfg & "MCSH=?;"
        strCfg = strCfg & "MCST=?;"
        strCfg = strCfg & "AUO2=?;"
        strCfg = strCfg & "GPED=?;"
        strCfg = strCfg & "GPIN=?;"
        strCfg = strCfg & "GPME=?;"
        strCfg = strCfg & "GPGA=?;"
        strCfg = strCfg & "GPMC=?;"
        strCfg = strCfg & "MCAE=?;"
        strCfg = strCfg & "PDMD=?;"
    End If
    CreateFullReadBackCmdMCA8000D = strCfg
End Function

Public Sub MakeDp5CmdList(ByRef strCfgArr As Collection)
    Dim isHVSE As Boolean
    Dim isPAPS As Boolean
    Dim isTECS As Boolean
    Dim isVOLU As Boolean
    Dim isCON1 As Boolean
    Dim isCON2 As Boolean
    Dim isINOF As Boolean
    Dim isBOOT As Boolean
    Dim isGATE As Boolean
    Dim isPAPZ As Boolean
    Dim isSCTC As Boolean
    Dim isDP5_DxK As Boolean
    Dim isDP5_DxL As Boolean
    
    If (STATUS.DEVICE_ID = dppMCA8000D) Then
        Call MakeDp5CmdListMCA8000D(strCfgArr)
        Exit Sub
    End If
    
    ' DP5 Rev Dx K,L needs PAPZ
    If ((STATUS.DEVICE_ID = dppDP5) And STATUS.isDP5_RevDxGains) Then
        If ((STATUS.DPP_ECO And &HF) = &HA) Then
            isDP5_DxK = True
        End If
        If ((STATUS.DPP_ECO And &HF) = &HB) Then
            isDP5_DxL = True
        End If
    End If

    isHVSE = CBool(((STATUS.DEVICE_ID <> dppPX5) And STATUS.PC5_PRESENT) Or (STATUS.DEVICE_ID = dppPX5))
    isPAPS = CBool((STATUS.DEVICE_ID <> dppDP5G) And (STATUS.DEVICE_ID <> dppTB5))
    isTECS = CBool(((STATUS.DEVICE_ID = dppDP5) And STATUS.PC5_PRESENT) Or (STATUS.DEVICE_ID = dppPX5) Or (STATUS.DEVICE_ID = dppDP5X))
    isVOLU = CBool(STATUS.DEVICE_ID = dppPX5)
    
    isCON1 = CBool((STATUS.DEVICE_ID <> dppDP5) And (STATUS.DEVICE_ID <> dppDP5X))
    isCON2 = CBool((STATUS.DEVICE_ID <> dppDP5) And (STATUS.DEVICE_ID <> dppDP5X))
    
    isINOF = CBool((STATUS.DEVICE_ID <> dppDP5G) And (STATUS.DEVICE_ID <> dppTB5))
    isSCTC = CBool((STATUS.DEVICE_ID = dppDP5G) Or (STATUS.DEVICE_ID = dppTB5))
    isBOOT = CBool((STATUS.DEVICE_ID = dppDP5) Or (STATUS.DEVICE_ID = dppDP5X))
    
    isGATE = CBool((STATUS.DEVICE_ID = dppDP5) Or (STATUS.DEVICE_ID = dppDP5X))
    isPAPZ = CBool((STATUS.DEVICE_ID = dppPX5) Or isDP5_DxK Or isDP5_DxL)
    
    strCfgArr.Add ("RESC")
    strCfgArr.Add ("CLCK")
    strCfgArr.Add ("TPEA")
    strCfgArr.Add ("GAIF")
    strCfgArr.Add ("GAIN")
    strCfgArr.Add ("RESL")
    strCfgArr.Add ("TFLA")
    strCfgArr.Add ("TPFA")
    strCfgArr.Add ("PURE")
    If (isSCTC) Then strCfgArr.Add ("SCTC")
    strCfgArr.Add ("RTDE")
    strCfgArr.Add ("MCAS")
    strCfgArr.Add ("MCAC")
    strCfgArr.Add ("SOFF")
    strCfgArr.Add ("AINP")
    If (isINOF) Then strCfgArr.Add ("INOF")
    strCfgArr.Add ("GAIA")
    strCfgArr.Add ("CUSP")
    strCfgArr.Add ("PDMD")
    strCfgArr.Add ("THSL")
    strCfgArr.Add ("TLLD")
    strCfgArr.Add ("THFA")
    strCfgArr.Add ("DACO")
    strCfgArr.Add ("DACF")
    strCfgArr.Add ("RTDS")
    strCfgArr.Add ("RTDT")
    strCfgArr.Add ("BLRM")
    strCfgArr.Add ("BLRD")
    strCfgArr.Add ("BLRU")
    If (isGATE) Then strCfgArr.Add ("GATE")
    strCfgArr.Add ("AUO1")
    strCfgArr.Add ("PRET")
    strCfgArr.Add ("PRER")
    strCfgArr.Add ("PREC")
    strCfgArr.Add ("PRCL")
    strCfgArr.Add ("PRCH")
    If (isHVSE) Then strCfgArr.Add ("HVSE")
    If (isTECS) Then strCfgArr.Add ("TECS")
    If (isPAPZ) Then strCfgArr.Add ("PAPZ")
    If (isPAPS) Then strCfgArr.Add ("PAPS")
    strCfgArr.Add ("SCOE")
    strCfgArr.Add ("SCOT")
    strCfgArr.Add ("SCOG")
    strCfgArr.Add ("MCSL")
    strCfgArr.Add ("MCSH")
    strCfgArr.Add ("MCST")
    strCfgArr.Add ("AUO2")
    strCfgArr.Add ("TPMO")
    strCfgArr.Add ("GPED")
    strCfgArr.Add ("GPIN")
    strCfgArr.Add ("GPME")
    strCfgArr.Add ("GPGA")
    strCfgArr.Add ("GPMC")
    strCfgArr.Add ("MCAE")
    If (isVOLU) Then strCfgArr.Add ("VOLU")
    If (isCON1) Then strCfgArr.Add ("CON1")
    If (isCON2) Then strCfgArr.Add ("CON2")
    If (isBOOT) Then strCfgArr.Add ("BOOT")
End Sub

Public Sub MakeDp5CmdListMCA8000D(ByRef strCfgArr As Collection)
    If (STATUS.DEVICE_ID = dppMCA8000D) Then
        strCfgArr.Add ("RESC")
        strCfgArr.Add ("PURE")
        strCfgArr.Add ("MCAS")
        strCfgArr.Add ("MCAC")
        strCfgArr.Add ("SOFF")
        strCfgArr.Add ("GAIA")
        strCfgArr.Add ("PDMD")
        strCfgArr.Add ("THSL")
        strCfgArr.Add ("TLLD")
        strCfgArr.Add ("GATE")
        strCfgArr.Add ("AUO1")
        strCfgArr.Add ("PRER")
        strCfgArr.Add ("PREL")
        strCfgArr.Add ("PREC")
        strCfgArr.Add ("PRCL")
        strCfgArr.Add ("PRCH")
        strCfgArr.Add ("SCOE")
        strCfgArr.Add ("SCOT")
        strCfgArr.Add ("SCOG")
        strCfgArr.Add ("MCSL")
        strCfgArr.Add ("MCSH")
        strCfgArr.Add ("MCST")
        strCfgArr.Add ("AUO2")
        strCfgArr.Add ("GPED")
        strCfgArr.Add ("GPIN")
        strCfgArr.Add ("GPME")
        strCfgArr.Add ("GPGA")
        strCfgArr.Add ("GPMC")
        strCfgArr.Add ("MCAE")
        strCfgArr.Add ("PDMD")
    End If
End Sub

Public Function GetCmdData(ByVal cstrCmd As String, ByVal cstrCfgData As String) As String
    Dim iStart As Integer
    Dim iEnd As Integer
    Dim iCmd As Integer
    Dim cstrCmdData As String

    GetCmdData = ""
    cstrCmdData = ""
    If (Len(cstrCfgData) < 7) Then Exit Function ' no data
    If (Len(cstrCmd) <> 4) Then Exit Function ' bad command
    iCmd = InStr(1, cstrCfgData, cstrCmd + "=", CompareMethod.Text)
    If (iCmd = 0) Then Exit Function ' cmd not found
    iStart = InStr(iCmd, cstrCfgData, "=")
    If (iStart = 0) Then Exit Function ' data start not found
    iEnd = InStr(iCmd, cstrCfgData, ";")
    If (iEnd = 0) Then GetCmdData = cstrCmdData ' data end found
    If (iStart >= iEnd) Then Exit Function ' data error
    cstrCmdData = Mid(cstrCfgData, iStart + 1, iEnd - (iStart + 1))
    GetCmdData = cstrCmdData
End Function

Public Function ReplaceCmdDesc(ByVal cstrCmd As String, ByRef cstrCfgData As String) As String
    Dim iStart As Integer
    Dim iCmd As Integer
    Dim cstrNew As String
    Dim cstrDesc As String

    ReplaceCmdDesc = cstrCfgData
    cstrNew = ""
    If (Len(cstrCfgData) < 7) Then Exit Function ' no data
    If (Len(cstrCmd) <> 4) Then Exit Function ' bad command
    iCmd = InStr(1, cstrCfgData, cstrCmd + "=")
    If (iCmd = 0) Then Exit Function ' cmd not found
    cstrDesc = GetCmdDesc(cstrCmd)
    If (Len(cstrDesc) = 0) Then Exit Function ' cmd desc  not found
    iStart = InStr(iCmd, cstrCfgData, "=")
    If (iStart <> (iCmd + 4)) Then Exit Function ' data start not found
    cstrNew = Left(cstrCfgData, iCmd - 1) & cstrDesc & Mid(cstrCfgData, iStart)
    ReplaceCmdDesc = cstrNew
End Function

Public Function AppendCmdDesc(ByRef cstrCmd As String, ByRef cstrCfgData As String) As String
    Dim iStart As Integer
    Dim iEnd As Integer
    Dim iCmd As Integer
    Dim cstrNew As String
    Dim cstrDesc As String

    AppendCmdDesc = cstrCfgData
    cstrNew = ""
    If (Len(cstrCfgData) < 7) Then Exit Function ' no data
    If (Len(cstrCmd) <> 4) Then Exit Function ' bad command
    iCmd = InStr(1, cstrCfgData, cstrCmd + "=")
    If (iCmd = 0) Then Exit Function ' cmd not found
    cstrDesc = GetCmdDesc(cstrCmd)
    If (Len(cstrDesc) = 0) Then Exit Function ' cmd desc  not found
    iStart = InStr(iCmd, cstrCfgData, "=")
    If (iStart <> (iCmd + 4)) Then Exit Function ' data start not found
    iEnd = InStr(iStart + 1, cstrCfgData, ";")
    If (iEnd > (iStart + 11)) Then Exit Function ' data end not found
    cstrNew = Left(cstrCfgData, iEnd) & "    " & cstrDesc & Mid(cstrCfgData, iEnd + 1)
    AppendCmdDesc = cstrNew
End Function

Public Function RemoveCmd(ByVal cstrCmd As String, ByVal cstrCfgData As String) As String
    Dim iStart As Integer
    Dim iEnd As Integer
    Dim iCmd As Integer
    Dim cstrNew As String
    Dim strLeft As String
    Dim strRight As String

    cstrNew = ""
    RemoveCmd = cstrCfgData
    If (Len(cstrCfgData) < 7) Then Exit Function ' no data
    If (Len(cstrCmd) <> 4) Then Exit Function ' bad command
    iCmd = InStr(1, cstrCfgData, cstrCmd + "=")
    If (iCmd = 0) Then Exit Function ' cmd not found
    iStart = iCmd
    iEnd = InStr(iCmd, cstrCfgData, ";")
    If (iEnd = 0) Then Exit Function
    If (iEnd <= iStart) Then Exit Function ' unknown error
    strLeft = Left(cstrCfgData, iStart - 1)
    strRight = Mid(cstrCfgData, iEnd + 1)
    cstrNew = strLeft & strRight
    RemoveCmd = cstrNew
End Function

'removes selected command by dpp device type
Public Function RemoveCmdByDeviceType(ByVal strCfgDataIn As String, PC5_PRESENT As Boolean, DppType As Byte, isDP5_RevDxGains As Boolean, DPP_ECO As Byte) As String
    Dim strCfgData As String
    Dim isHVSE As Boolean
    Dim isPAPS As Boolean
    Dim isTECS As Boolean
    Dim isVOLU As Boolean
    Dim isCON1 As Boolean
    Dim isCON2 As Boolean
    Dim isINOF As Boolean
    Dim isBOOT As Boolean
    Dim isGATE As Boolean
    Dim isPAPZ As Boolean
    Dim isSCTC As Boolean
    Dim isPREL As Boolean
    Dim isDP5_DxK As Boolean
    Dim isDP5_DxL As Boolean
    
    strCfgData = strCfgDataIn
    If (DppType = dppMCA8000D) Then
        strCfgData = Remove_MCA8000D_Cmds(strCfgData, DppType)
        RemoveCmdByDeviceType = strCfgData
    End If
    
    ' DP5 Rev Dx K,L needs PAPZ
    If ((DppType = dppDP5) And isDP5_RevDxGains) Then
        If ((DPP_ECO And &HF) = &HA) Then
                isDP5_DxK = True
        End If
        If ((DPP_ECO And &HF) = &HB) Then
                isDP5_DxL = True
        End If
    End If

    isHVSE = CBool(((DppType <> dppPX5) And PC5_PRESENT) Or (DppType = dppPX5))
    isPAPS = CBool((DppType <> dppDP5G) And (DppType <> dppTB5))
    isTECS = CBool(((DppType = dppDP5) And PC5_PRESENT) Or (DppType = dppPX5) Or (DppType = dppDP5X))
    isVOLU = CBool(DppType = dppPX5)
    isCON1 = CBool((DppType <> dppDP5) And (DppType <> dppDP5X))
    isCON2 = CBool((DppType <> dppDP5) And (DppType <> dppDP5X))
    isINOF = CBool((DppType <> dppDP5G) And (DppType <> dppTB5))
    isSCTC = CBool((DppType = dppDP5G) Or (DppType = dppTB5))
    isBOOT = CBool((DppType = dppDP5) Or (DppType = dppDP5X))
    isGATE = CBool((DppType = dppDP5) Or (DppType = dppDP5X))
    isPAPZ = CBool((DppType = dppPX5) Or isDP5_DxK Or isDP5_DxL)
    isPREL = CBool(DppType = dppMCA8000D)
    If (Not isHVSE) Then strCfgData = RemoveCmd("HVSE", strCfgData)     'High Voltage Bias
    If (Not isPAPS) Then strCfgData = RemoveCmd("PAPS", strCfgData)     'Preamp Voltage
    If (Not isTECS) Then strCfgData = RemoveCmd("TECS", strCfgData)     'Cooler Temperature
    If (Not isVOLU) Then strCfgData = RemoveCmd("VOLU", strCfgData)     'px5 speaker
    If (Not isCON1) Then strCfgData = RemoveCmd("CON1", strCfgData)     'connector 1
    If (Not isCON2) Then strCfgData = RemoveCmd("CON2", strCfgData)     'connector 2
    If (Not isINOF) Then strCfgData = RemoveCmd("INOF", strCfgData)     'input offset
    If (Not isBOOT) Then strCfgData = RemoveCmd("BOOT", strCfgData)     'PC5 On At StartUp
    If (Not isGATE) Then strCfgData = RemoveCmd("GATE", strCfgData)     'Gate input
    If (Not isPAPZ) Then strCfgData = RemoveCmd("PAPZ", strCfgData)     'Pole-Zero
    If (Not isSCTC) Then strCfgData = RemoveCmd("SCTC", strCfgData)     'Scintillator Time Constant
    If (Not isPREL) Then strCfgData = RemoveCmd("PREL", strCfgData)     'Preset Live Time
    RemoveCmdByDeviceType = strCfgData
End Function

''removes MCA8000D commands
Public Function Remove_MCA8000D_Cmds(strCfgDataIn As String, DppType As Byte) As String
    Dim strCfgData As String
    
    strCfgData = strCfgDataIn
    If (DppType = dppMCA8000D) Then
        strCfgData = RemoveCmd("CLCK", strCfgData)
        strCfgData = RemoveCmd("TPEA", strCfgData)
        strCfgData = RemoveCmd("GAIF", strCfgData)
        strCfgData = RemoveCmd("GAIN", strCfgData)
        strCfgData = RemoveCmd("RESL", strCfgData)
        strCfgData = RemoveCmd("TFLA", strCfgData)
        strCfgData = RemoveCmd("TPFA", strCfgData)
        'strCfgData = RemoveCmd("PURE", strCfgData)
        strCfgData = RemoveCmd("RTDE", strCfgData)
        strCfgData = RemoveCmd("AINP", strCfgData)
        strCfgData = RemoveCmd("INOF", strCfgData)
        strCfgData = RemoveCmd("CUSP", strCfgData)
        strCfgData = RemoveCmd("THFA", strCfgData)
        strCfgData = RemoveCmd("DACO", strCfgData)
        strCfgData = RemoveCmd("DACF", strCfgData)
        strCfgData = RemoveCmd("RTDS", strCfgData)
        strCfgData = RemoveCmd("RTDT", strCfgData)
        strCfgData = RemoveCmd("BLRM", strCfgData)
        strCfgData = RemoveCmd("BLRD", strCfgData)
        strCfgData = RemoveCmd("BLRU", strCfgData)
        strCfgData = RemoveCmd("PRET", strCfgData)
        strCfgData = RemoveCmd("HVSE", strCfgData)
        strCfgData = RemoveCmd("TECS", strCfgData)
        strCfgData = RemoveCmd("PAPZ", strCfgData)
        strCfgData = RemoveCmd("PAPS", strCfgData)
        strCfgData = RemoveCmd("TPMO", strCfgData)
        strCfgData = RemoveCmd("SCAH", strCfgData)
        strCfgData = RemoveCmd("SCAI", strCfgData)
        strCfgData = RemoveCmd("SCAL", strCfgData)
        strCfgData = RemoveCmd("SCAO", strCfgData)
        strCfgData = RemoveCmd("SCAW", strCfgData)
        strCfgData = RemoveCmd("BOOT", strCfgData)

        ' added to list late, recheck at later date 20120817
        strCfgData = RemoveCmd("CON1", strCfgData)
        strCfgData = RemoveCmd("CON2", strCfgData)

        ' not implemented as of 20120817, will be implemented at some time
        strCfgData = RemoveCmd("VOLU", strCfgData)
    End If
    Remove_MCA8000D_Cmds = strCfgData
End Function

Public Function GetCmdChunk(strCmd As String) As Long
    Dim idxCfg As Long
    Dim lChunk As Long
    Dim lEnd As Long
    GetCmdChunk = 0
    lChunk = 0
    lEnd = 0
    For idxCfg = 1 To Len(strCmd)
        lChunk = InStr(lEnd + 1, strCmd, ";")
        If ((lChunk = 0) Or (lChunk > 512)) Then Exit For
        lEnd = lChunk
    Next
    GetCmdChunk = lEnd
End Function

Public Function ReplaceText(ByVal strInTextIn As String, ByVal strFrom As String, ByVal strTo As String) As String
    Dim strInText As String
    Dim strOutText As String
    Dim lFromLen As Long
    Dim lMatchPos As Long

    strInText = strInTextIn
    strOutText = ""
    lFromLen = Len(strFrom)
    Do While Len(strInText) > 0
        lMatchPos = InStr(strInText, strFrom)
        If lMatchPos = 0 Then
            strOutText = strOutText & strInText
            strInText = ""
        Else
            strOutText = strOutText & Left(strInText, lMatchPos - 1) & strTo
            strInText = Mid(strInText, lMatchPos + lFromLen)
        End If
    Loop
    ReplaceText = strOutText
End Function

Public Function CreateResTestReadBackCmd(bSendCoarseFineGain As Boolean) As String
    Dim strCfg As String
    Dim isINOF As Boolean

    isINOF = (STATUS.DEVICE_ID <> dppDP5G) And (STATUS.DEVICE_ID <> dppTB5)
    strCfg = ""
    strCfg = strCfg & "CLCK=?;"
    strCfg = strCfg & "TPEA=?;"
    If (bSendCoarseFineGain) Then strCfg = strCfg & "GAIF=?;"
    If (Not bSendCoarseFineGain) Then strCfg = strCfg & "GAIN=?;"
    strCfg = strCfg & "RESL=?;"
    strCfg = strCfg & "TFLA=?;"
    strCfg = strCfg & "TPFA=?;"
    strCfg = strCfg & "PURE=?;"
    strCfg = strCfg & "RTDE=?;"
    strCfg = strCfg & "MCAS=?;"
    strCfg = strCfg & "MCAC=?;"
    strCfg = strCfg & "SOFF=?;"
    strCfg = strCfg & "AINP=?;"
    If (isINOF) Then strCfg = strCfg & "INOF=?;"
    If (bSendCoarseFineGain) Then strCfg = strCfg & "GAIA=?;"
    CreateResTestReadBackCmd = strCfg
End Function

''''Private Sub SendCfgToHwExample(strCfg As String)
'''''For SCAs'Private Sub SendCfgToHwExample(strCfg As String, sca As scaSetup)
''''    Dim idxCmd As Long
''''    Dim strDisplay As String
''''    Dim strCmd As String
''''    Dim curStart As Currency            'start time from system time in milliseconds
''''    Dim TimeExpired As Boolean          'time expired flag
''''    Dim curElapsed As Currency          'Elapsed time from start time in milliseconds
''''    Dim lCfgLen As Long                 'ASCII Configuration Command String Length
''''    Dim idxSplitCfg As Long             'Configuration split position, only if necessary
''''    Dim bSplitCfg As Boolean            'Configuration split flag
''''    Dim strSplitCfg As String           'Configuration split string second buffer
''''
''''    bSplitCfg = False
''''    strDisplay = ""
''''    If (Len(strCfg) = 0) Then Exit Sub   'not initialized
''''    strCfg = TypeName(varConfig)             'test variant data type
''''    If (strCfg = "String()") Then           'have data
''''        strCfg = ""                         'clear cfg storage
''''    Else
''''        Exit Sub                            'no data
''''    End If
''''    For idxCmd = 0 To UBound(varConfig, 1)
''''        strCmd = varConfig(idxCmd, 0) & "=" & varConfig(idxCmd, 1) & ";"
''''        If (Not (InStr(strCmd, "RESC") > 0)) Then
''''            If (Len(Trim(varConfig(idxCmd, 1))) > 0) Then
''''                strCfg = strCfg & strCmd
''''                strDisplay = strDisplay & strCmd & vbNewLine
''''            Else
''''                strDisplay = strDisplay & ";" & strCmd & vbNewLine
''''            End If
''''        End If
''''    Next
''''    strCfg = "RESC=YES;" & strCfg
''''    strCfg = UCase(strCfg)
''''    strCfg = RemoveCmdByDeviceType(strCfg, STATUS.PC5_PRESENT, STATUS.DEVICE_ID)
''''    Clipboard.SetText strCfg
''''    strDisplay = "RESC=YES;" & vbNewLine & strDisplay
''''    strDisplay = UCase(strDisplay)
''''    'txtSendCfgToHwNoEdit = strDisplay
''''
''''    'Test configuration size
''''    lCfgLen = Len(strCfg)
''''    If (lCfgLen > 512) Then     'configuration is too large, try to reduce
''''        strCfg = ReplaceText(strCfg, "US;", ";")
''''        strCfg = ReplaceText(strCfg, "OFF;", "OF;")
''''        strCfg = ReplaceText(strCfg, "RISING;", "RI;")
''''        strCfg = ReplaceText(strCfg, "FALLING;", "FA;")
''''        lCfgLen = Len(strCfg)
''''        If (lCfgLen > 512) Then 'configuration is still too large, split cfg
''''            bSplitCfg = True
''''            idxSplitCfg = GetCmdChunk(strCfg)
''''            strSplitCfg = Mid(strCfg, idxSplitCfg + 1)
''''            strCfg = Left(strCfg, idxSplitCfg)
''''        End If
''''    End If
''''
''''    'MsgBox strCfg
''''    'MsgBox strSplitCfg
''''
''''    'lblCfgLenValue = CStr(Len(strCfg))
''''    s.HwCfgReady = False
''''    s.HwCfgExReady = False
''''    s.HwCfgDP5Out = strCfg
''''    If (Len(strCfg) > 0) Then
''''        s.HwCfgReady = True
''''        frmDP5.SendCommand XMTPT_SEND_CONFIG_PACKET_TO_HW
''''        s.HwCfgReady = False
''''    End If
''''
''''    If (bSplitCfg) Then             'send second configuration block
''''        TimeExpired = False
''''        'lblPleaseWait.Visible = True
''''        curStart = msTimeStart()
''''        Do                          'wait for cfg packet to be processed
''''            DoEvents
''''            curElapsed = msTimeDiff(curStart)
''''            TimeExpired = msTimeExpired(curStart, 200)    '200 milliseconds wait
''''        Loop Until (TimeExpired)
''''        'lblPleaseWait.Visible = False
''''        s.HwCfgReady = False
''''        s.HwCfgExReady = False
''''        s.HwCfgDP5Out = strSplitCfg
''''        If (Len(strCfg) > 0) Then
''''            s.HwCfgReady = True
''''            frmDP5.SendCommand XMTPT_SEND_CONFIG_PACKET_TO_HW
''''            s.HwCfgReady = False
''''        End If
''''    End If
''''
'''''For SCAs'    If (s.SCAEnabled And s.isDppConnected) Then
'''''For SCAs'        TimeExpired = False
'''''For SCAs'        'lblPleaseWait.Visible = True
'''''For SCAs'        curStart = msTimeStart()
'''''For SCAs'        Do                          'wait for cfg packet to be processed
'''''For SCAs'            DoEvents
'''''For SCAs'            curElapsed = msTimeDiff(curStart)
'''''For SCAs'            TimeExpired = msTimeExpired(curStart, 200)    '200 milliseconds wait
'''''For SCAs'        Loop Until (TimeExpired)
'''''For SCAs'        'lblPleaseWait.Visible = False
'''''For SCAs'        strCfg = SCAStringALL(sca, True)
'''''For SCAs'        s.HwCfgReady = False
'''''For SCAs'        s.HwCfgExReady = False
'''''For SCAs'        s.HwCfgDP5Out = strCfg
'''''For SCAs'        If (Len(strCfg) > 0) Then
'''''For SCAs'            s.HwCfgReady = True
'''''For SCAs'            frmDP5.SendCommand XMTPT_SEND_CONFIG_PACKET_TO_HW
'''''For SCAs'            s.HwCfgReady = False
'''''For SCAs'        End If
'''''For SCAs'    End If
''''
''''End Sub
''''