; Orange programmer module v3.0
; (c) 2010-2014 CnCLab

;CHIP=PIC16F716,2Kx14,P16F716.hpl
;AREA=CODE,2Kx14,0,0
;AREA=CONFIG,1x14,0,0x400E


; Primary Tested PIC16F716

; DS40245b

ALLPINS=18
OPTIONS=f,
INFO="PIC Adapter"

PING=SDA,1,13 ;RB7
PINO=CLK,0,12 ;RB6
PINO=MCLR,5,4  ;/MCLR

PING=GND,255,5  ;Vss
PINO=VCC,254,14

CDELAY=2


R1=CONFIG,H
R10=CP,L,On,Off
R11=BORV,L,"0 : 2.5V,1 : 4.0V"
R12=BOREN,L,0:Off,1:On
R13=PWRTE,L,0:On,1:Off
R14=WDTE,L,0:Off,1:On
R15=FOSC,L,00:LP,01:XT,10:HS,11:RC

[_PULSE]
CLK=1,P=3,CLK=0,P=3

[_COMMAND]
; R0 - CMD
P=1
LOOP=(0,5){SDA=R0[I],CLK=P}
P=1

[_OUTWORD]
SDA=0,CLK=1,CLK=0
LOOP=(0,13){SDA=R0[I],_PULSE}
SDA=0,CLK=1,CLK=0


[_INCADD]
R8=ADR
LOOP=(0,0xFFFF){  ;increment address to current value!
R9?R8{BREAK}
R0=6,_COMMAND ;INCADD
R9=+1
}

[INIT]
VPP=0
MCLR=0,CLK=1,SDA=1
PRINT=S("Power up...")
$VERSION=/65536
$VERSION?3{
P=200000     ;charge MCLR cap!
CLK=0,SDA=0
IDISABLE
VCC=0
P=25000                ;no more time 25000!
VCC=1
VPP=12800
MCLR=1            ;Vcc pulse for re-enter prg mode
IENABLE                       ;Programm/Verify Mode!

}

$VERSION?!3{
CLK=0,SDA=0,P=100
VPP=12800
MCLR=1            ;Vcc pulse for re-enter prg mode
}

P=1000
SDA=1

P=150000
PRINT=S(" ")

R9=0 ;current address register


;-------------------------------------------------
[_FUSE2BIT]
; unpack config word
;13 12 11 10 9 8  7     6   5 4   3    2     1     0
;CP -  -  -  - - BORV BOREN - - PWRTE WDTE FOSC1 FOSC0

R10=0,R11=0,R12=0,R13=0,R14=0,R15=0

R15[0]=R1[0],R15[1]=R1[1] ;FOSC
R14[0]=R1[2]	;WDTE
R13[0]=R1[3]	;PWRTE
R12[0]=R1[6]	;BODEN	
R11[0]=R1[7]	;BORV
R10[0]=R1[13]	;CP


[_BIT2FUSE]
;copy separate bits to config word
R1=0x3FFF

R1[0]=R15[0],R1[1]=R15[1] ;FOSC
R1[2]=R14[0]	;WDTE
R1[3]=R13[0]	;PWRTE
R1[6]=R12[0]	;BODEN	
R1[7]=R11[0]	;BORV
R1[13]=R10[0]	;CP

;PRINT=("Configuration Word = %04lX",R1)

[_READFUSES]
R0=0,_COMMAND ;LDCONF
R0=0x3FFF,_OUTWORD	; dummy
ADR=0

LOOP=(0,6){ 			; goto adr 0x2007
R0=4,_COMMAND ;RDPROG
SDA=1,_PULSE
LOOP=(0,13){_PULSE}   		;dummy read...
SDA=0,_PULSE
ADR=+1
_INCADD
}

R0=4,_COMMAND ;RDPROG
SDA=0,_PULSE
R1=0
LOOP=(0,13){_PULSE,SDA=1,R1[I]=SDA,SDA=0}
SDA=1,_PULSE
;PRINT=("Configuration Word = %04lX",R1)
ADR=0
DATA=R1


[_WRITEFUSES]
R1=DATA
ADR=0
R0=0,_COMMAND ;LDCONF
R0=0x3FFF,_OUTWORD	; dummy

LOOP=(0,6){ 		; goto adr 0x2007
R0=2,_COMMAND 		; LDPROG
R0=0x3FFF,_OUTWORD	; dummy data
;R0=8,_COMMAND 		; BEGPRG - don't really programm
;P=10000
P=100
ADR=+1
_INCADD
}

R0=2,_COMMAND 		;LDPROG
R0=R1,_OUTWORD		;config
_COMMAND(0x18) ;BEGPRG
P=10000
_COMMAND(0x0E) ;ENDPRG


; check?
R0=4,_COMMAND ;RDPROG
SDA=0,_PULSE
R2=0x3FFF
LOOP=(0,13){_PULSE,SDA=1,R2[I]=SDA,SDA=0}
SDA=1,_PULSE
R1?!R2{PRINT=("Write error!")}

;-------------------------------------------------

[READ]
$AREA?1{_READFUSES,RETURN}
_INCADD
R0=4          ;RDPROG
_COMMAND

SDA=1,_PULSE
R0=0
LOOP=(0,13){_PULSE,R0[I]=SDA}
SDA=1,_PULSE
DATA=R0 ;For Orange5 только через регистр!
;CLK=1,CLK=0
;R0=6,_COMMAND ;INCADD

[WRITE]
$AREA?1{_WRITEFUSES,EXIT}
_INCADD

_COMMAND(2)   ;LDPROG

SDA=0,CLK=1,CLK=0
LOOP=(0,13){SDA=DATA[I],_PULSE}
SDA=0,CLK=1,CLK=0

_COMMAND(0x18) ;BEGPRG
P=5000
_COMMAND(0x0E) ;ENDPRG

[~!#"Fuse Editor"]
$AREA=1	;FUSES
R1=DATA
_FUSE2BIT
GET=("Edit Fuses",R10,R11,R12,R13,R14,R15)
RA?0{EXIT}
_BIT2FUSE
DATA=R1


[Erase]
ADR=0
P=10000
R0=0,_COMMAND ;LDCONF
R0=03FFFH,_OUTWORD
R0=6,LOOP=(0,6){_COMMAND} ;INCADD  goto 2007
R0=9,_COMMAND ;Bulk Erase
P=20000
P=10000


[END]
VPP=0
MCLR=0,CLK=0,SDA=0



["Read ID"]
R0=0,_COMMAND ;LDCONF
R0=0x3FFF,_OUTWORD	; dummy
ADR=0

LOOP=(0,5){ 			; goto adr 0x2007
_COMMAND(4) ;RDPROG
SDA=1,_PULSE
LOOP=(0,13){_PULSE}   		;dummy read...
SDA=0,_PULSE
ADR=+1
_INCADD
}

_COMMAND(4) ;RDPROG
SDA=0,_PULSE
R1=0
LOOP=(0,13){_PULSE,SDA=1,R1[I]=SDA,SDA=0}
SDA=1,_PULSE
R2=R1
R2=&3FE0H ;id mask

R2?1140H{PRINT=("ID = %04lX - PIC16F716",R1),EXIT}
PRINT=("ID = %04lX",R1)