; Orange programmer module v3.8 beta
; (c) 2001-2012 CnCLab
; Atmel AVR
; CHIP=ATmega128,128K
; FLASH - 128K
; EEPROM - 4K
; Primary tested

; SPI mapped to port E!!!!!


ALLPINS=0 ;=64
INFO="AVR Adapter"
OPTIONS=mf,   ;FLASH: no modify, skip blank

PINO=SCK,  0	;11 PB1
PINO=MOSI, 2    ;2  PE0
PINO=MISO, 1    ;3  PE1
PINO=RESET,3    ;20 RESET
PINI=MISO, 1

;PINO=GND,255   ;22,53,63
;PINO=VCC,254   ;21,52,64 Vcc,AVcc
;OSC		;23 XTAL2 
BUSO=CFREQ,128

R8=Fuses,B8
R9=Lock,C6,BLB12,BLB11,BLB02,BLB01,LB2,LB1
R10=CKSEL,L,"0000: Ext Clk,0001: IntRC 1MHz,0010: IntRC 2MHz,0011: IntRC 4MHz,0100: IntRC 8MHz,0101: ExtRC 0.9MHz,0110: ExtRC 0.9-3.0M,0111: ExtRC 3.0-8.0M,1000: ExtRC 8.0-12.0M,1001: LowFreq Crystal,1010: Crystal/Ceramic,1011: Crystal/Ceramic,1100: Crystal 0.9-3.0,1101: Crystal 0.9-3.0,1110: Crystal 3.0-8.0,1111: Crystal 3.0-8.0"
;R11=SUT,L,00,01,10,11
R11=SUT,C2
R12=BODEN,L,"0 - On,1 - Off"
R13=BODLEVEL,L,"0 - High,1 - Low"
R14=BOOTRST,L,"0 - Boot Loader","1 - Application"
R15=BOOTSZ,L,"32 pages,16 pages,8 pages,4 pages"
R16=EESAVE,L,"0 - Save,1 - Clear"
R17=CKOPT,L,"0 - On,1 - Off"
R18=JTAGEN,L,"0 - On,1 - Off"
R19=OCDEN,L,"0 - On,1 - Off"

R1A=WDTON,L,"0 - On,1 - Off"
R1B=M103C,L,"0 - On,1 - Off"

CDELAY=10 ; minimum periods for the serial clock (SCK) > 4 XTAL1 clock cycle!


[_DOUT]
R1=0;
LOOP=(7,0){MOSI=R0[I],SCK=1,R1[I]=MISO,SCK=0}

[_DIN]
R0=0
LOOP=(7,0){SCK=1,R0[I]=MISO,SCK=0}




[INIT]
SCK=0
MISO=Z
CFREQ=2000000
RESET=0,P=1000

LOOP=(0,31){    ; 32 attempts
RESET=1,P=150
RESET=0,P=20000
R0=0xAC,_DOUT ;Programming Enable
R0=0x53,_DOUT
R0=0x00,_DOUT
R3=R1
R0=0x00,_DOUT
R3?0x53{BREAK}
;PRINT=("ANSWER: %02lX",R1)
}
R3?!0x53{PRINT=("ANSWER ERROR: %02lX",R3),EXIT}

P=10



[READ]
$AREA?0{
R0=0x20            ;program flash memory area
R1=ADR,R0[3]=R1[0] ;Hi/Lo
_DOUT
LOOP=(16,9){MOSI=ADR[I],SCK=P}
LOOP=(8,1){MOSI=ADR[I],SCK=P}
}
$AREA?1{
R0=0xA0      ;eeprom area
_DOUT
LOOP=(15,8){MOSI=ADR[I],SCK=P}
LOOP=(7,0){MOSI=ADR[I],SCK=P}
}

_DIN		;common
DATA=R0


[WRITE]
$AREA?0{
PRINT=("Only Page Write Supported!")
EXIT
}

$AREA?1{
R0=0xC0 ;eeprom memory area 
_DOUT
LOOP=(15,8){MOSI=ADR[I],SCK=P}
LOOP=(7,0){MOSI=ADR[I],SCK=P}
R0=DATA,_DOUT
P=10000 ; EEPROM min 9ms
}


[WRITEBLOCK]
R7=ADR	;check empty (0xFF) block
LOOP=($BLOCKSIZE){
R1=DATA
R1?!0xFF{BREAK}
ADR=+1
}
R1?0xFF{RETURN}
ADR=R7

LOOP=($BLOCKSIZE){
R0=0x40 ;program memory
R1=ADR,R0[3]=R1[0],_DOUT 	;Hi/Lo
R0=0,_DOUT
LOOP=(8,1){MOSI=ADR[I],SCK=P}
R0=DATA,_DOUT
P=5
ADR=+1
}
;Write Program memory Page:
ADR=R7
_DOUT(0x4C) 
LOOP=(16,9){MOSI=ADR[I],SCK=P}
LOOP=(8,6){MOSI=ADR[I],SCK=P}
LOOP=(5,1){MOSI=0,SCK=P}
_DOUT(0) 		;dummy data
P=5000

[WRITEEND]
P=10000
RESET=1,P=20
RESET=0,P=20000




["Read Fuses"]
R10=0,R11=0,R12=0,R13=0
R14=0,R15=0,R16=0,R17=0
R18=0,R19=0,R1A=0,R1B=0

R0=0x50,_DOUT	;Read Fuse LOW
R0=0x00,_DOUT
R0=0x00,_DOUT
_DIN
PRINT=L("%02X ",R0)

R10=R0,R10=&0xF	;R10=CKSEL,L
R11[0]=R0[4]    ;R11=SUT,L,1,2,3,4           
R11[1]=R0[5]
R12[0]=R0[6]    ;R12=BODEN,L,On,Off            
R13[0]=R0[7]    ;R13=BODLEVEL,L,High,Low 

R0=0x58,_DOUT   ;Read Fuse High 
R0=0x08,_DOUT
R0=0x00,_DOUT
_DIN
PRINT=L("%02X ",R0)

R14[0]=R0[0]	;R14=BOOTRST,C1
R15[0]=R0[1]	;R15=BOOTSZ,L,"32 pages,16 pages,8 pages,4 pages"
R15[1]=R0[2]	
R16[0]=R0[3]	;R16=EESAVE
R17[0]=R0[4]	;R17=CKOPT
;SPIEN not accessible
R18[0]=R0[6]	;R18=JTAGEN
R19[0]=R0[7]	;R18=OCDEN



R0=0x50,_DOUT   ;Read Fuse ext
R0=0x08,_DOUT
R0=0x00,_DOUT
_DIN
PRINT=L("%02X ",R0)
RESET=1,P=10
VCC=0

R1A[0]=R0[0]	;WDTON
R1B[0]=R0[1]	;M103C



GET=("Read Fuses",R10,R11,R12,R13,R14,R15,R16,R17,R18,R19, R1A,R1B)
;GET=("Read Fuses",R10,R11,R12,R13,R14)


["Write Fuses"]
GET=("Write Fuses",R10,R11,R12,R13,R14,R15,R16,R17,R18,R19, R1A,R1B)
;PRINT=("%lX",R11)
RA?0{EXIT}
R10?0{
PRINT=A("This fuses value require Ext. Clock, continue?")
RA?0{EXIT}
}

R8=0

R8=R10,R8=&0xF	;R10=CKSEL,L
R8[4]=R11[0]   ;R11=SUT,L,1,2,3,4           
R8[5]=R11[1]
R8[6]=R12[0]   ;R12=BODEN,L,On,Off            
R8[7]=R13[0]   ;R13=BODLEVEL,L,High,Low 

R0=0xAC,_DOUT
R0=0xA0,_DOUT
R0=0x00,_DOUT
R0=R8,_DOUT
P=10000

R8=0xFF
R8[0]=R14[0]	;R14=BOOTRST,C1
R8[1]=R15[0]	;R15=BOOTSZ,L,"32 pages,16 pages,8 pages,4 pages"
R8[2]=R15[1]	
R8[3]=R16[0]	;R16=EESAVE,C1
R8[4]=R17[0]	;R17=CKOPT,C1
R8[6]=R18[0]	;R1A=
R8[7]=R19[0]	;R19=S8515C,C1

R0=0xAC,_DOUT   ;Write High Fuse
R0=0xA8,_DOUT
R0=0x00,_DOUT
R0=R8,_DOUT
P=10000


R8=0xFF
R8[0]=R1A[0]	;
R8[1]=R1B[0]	;

R0=0xAC,_DOUT   ;Write Ext Fuse
R0=0xA4,_DOUT
R0=0x00,_DOUT
R0=R8,_DOUT
P=10000



RESET=1,P=20
RESET=0,P=20000


[ReadLock]
R0=0x58,_DOUT ;Write lock bits
R0=0x00,_DOUT 
R0=0x00,_DOUT 
_DIN
R9=R0
GET=("Lock",R9)

[WriteLock]
GET=("Write Lock",R9)
R0=0xAC,_DOUT ;Write lock bits
R0=0xE0,_DOUT 
R0=0x00,_DOUT 
R0=R9,R0=|0xC0,_DOUT 

P=10000
RESET=1,P=20,
RESET=0,P=20000

[READID]
R0=0x30,_DOUT
R0=0x00,_DOUT
R0=0x00,_DOUT
_DIN
R2=R0,R2=<<8

R0=0x30,_DOUT
R0=0x00,_DOUT
R0=0x01,_DOUT
_DIN
R2=|R0,R2=<<8

R0=0x30,_DOUT
R0=0x00,_DOUT
R0=0x02,_DOUT
_DIN
R0=|R2

;R2?0x1E9702{PRINT=("ID: %06lX - ATmega128",R2),EXIT}
PRINT=S("ID: %06lX",R0)



[Erase]
R0=0xAC,_DOUT ;Chip Erase
R0=0x80,_DOUT 
R0=0x00,_DOUT 
R0=0x00,_DOUT 

P=50000
RESET=1,P=20,
RESET=0,P=20000



[END]
RESET=1
;EO=1,P=10 ;BB off